How To Program A Key Fob Chevy Sonic

September 21, 2021 Post a Comment

For vehicles with regular ignition that use a transponder key or a flip key: Programming with two working keys:

Replacement Folding 4 Buttons Remote Key Case Shell Entry

If all keys are lost.

How to program a key fob chevy sonic. Insert a working flip key into the ignition and turn to the on/run position (just shy of cranking engine). After the engine has started, turn the key to off and remove the key. Now on the chevy key fob, press and hold both the unlock and lock buttons until you hear the door locks engage and disengage again.

13504199, 13500221, 23335584, 13587072, strattec 5912545). Here are the steps you should take to program an additional chevy key: Genuine, original oem (factory gm) remote.

On your chevy key fob, press and hold the unlock and lock buttons simultaneously until you hear the door locks engage and disengage again, indicating that you have successfully programmed your key fob. Insert programmed master key transmitter into ignition. When the key is programmed, the dic will show that it is ready to program the next key.

Insert the key to be programmed and turn it to on within 10 seconds of removing the original key. Guaranteed high quality oem electronic keyless entry remote flip key fob (fcc id: The key must be placed with the buttons facing down.

Within 5 seconds, insert the new flip key into the ignition and turn to the on/run. 2014 chevrolet sonic remote programming insert the original, already programmed key in the ignition and start the engine. Key blade must be cut to work in your ignition before you begin.

Remove the smart key from the transmitter pocket and press the unlock button on the smart key. If you find a small roll pin punch you can push the pin out of the old fob and get the straight cut key portion. A maximum of 8 key transmitters can be programmed.

The first step is to press the silver button at the top corner of the key fob to eject the flip out or switchblade style metal ignition key. Insert the original, already programmed key in the ignition and turn the key to the on/run position. Get inside your vehicle and make sure all doors are shut.

2017 chevrolet sonic key programming. Now you know what it does, so lets learn how to program a chevy key fob. Programming with one recognized transmitter to program a new key.

To program additional keys, repeat steps 3 through 5. Wait 5 seconds or until flashing security light goes off. Lock, unlock, trunk release, remote start, panic.

The part the broke on the old key is more than likely at pinned joint. Unlock the drivers side door manually. Push the pin out of the new fob and remove the solid blank.

Turn the ignition cylinder to on position and right after to off position. Insert new key and turn on (do not start!). When the smart key is recognized by the vehicle, the dic display will show that it is ready to program the next smart key.

Turn the flip key to the off/lock position and remove it. Insert the vehicle key of the transmitter into the key lock cylinder on the outside of the driver door and turn the key to. Place the new key into the key pocket.

This symbolizes that you have successfully programmed your chevy key fob! Cycle the key to the on position (do not start the engine) and then off one time, then remove the key from the ignition. Remove the key from the key slot and press the unlock button.

2013 chevrolet sonic key programming. Insert the original, already programmed key in the ignition and start the engine. How to program a 2014 chevrolet sonic keyless entry remote fob smart key.

Same as the remote you can purchase at your local chevrolet dealership. 2012 2013 2014 2015 2016 2017 2018 2019 2020 chevrolet sonic sedan. After the engine has started, turn the key to off and remove the key.

Move the old cut portion over to the new electronic fob, program the fob and you should be good to go. Within 10 seconds insert new key and turn on. Step by step how to programming instructions:

The vehicle must be off and all of the transmitters you wish to program must be with you. Insert the original, already programmed key in the ignition and turn to the key to the on. Press and hold the vehicle on/off switch for two seconds.

This universal method will work whether youve got a chevy malibu or chevy silverado key fob. Then insert your thumb in to the void on the side of the fob where the ignition key used to reside and gently pop off the rear battery cover. Remove the key lock cylinder cap on the driver door handle.

Press any button on your remote for two seconds and wait for the locks to click to indicate successful programming of the remote and the end of the procedure. Insert the original, already programmed key in the ignition and start the engine. Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.

You can reinsert the newly programmed key back into the ignition, turning to the on position to end the programming. After the engine has started, turn the key off and remove the key. Below are programming instructions for the keyless entry remotes on various chevrolet vehicles, including chevy cars and trucks.

Then you must perform what we call the 10x10x10 procedure: The new key to be programmed needs to be cut prior to performing this programming procedure.

Pin on AntiTheft Accessories